(The following is a morphine pill preparation method, known as "crisping", that allows you to more easily draw the sloution into a syringe. As you may know, the current formula for many narcotic pills has been altered to make them gel up when water is added. This was done intentionally to make them more difficult to prepare for injection. Well, to all the assholes that participated in making them more difficult to inject, FUCK YOU! By following these simple instructions, you should be able to narcotic pills with much greater ease. No problems with the solution gelling up and being a real bitch to draw up into the syringe. Thanks to "Mobius Dick" for this informative post, which I found on a google group for hard drug users. Enjoy!)
After many months of working with this technique, I have come up with
the definitive way to inject MS Contins, Oxycontin's, and MSIR.
Although many of you still may have success with older pills and other
methods, the newer pills require a trick or two to get them into
solution.
Since most people get the 100 mg MS Contins and since the OCs are about
the same size, I will use this as my standard. I also use a wheel
filter for all pills now as I have gotten trash fever from a certain
pills other than MSCs and OCs, but rather than take the chance, I use
it all the time. I also use a 50 ml Pyrex or Kimax beaker, but a spoon
can be used; however, it is more work and you risk spilling it. If you
do use a spoon, use a large one, bigger than a tablespoon to contain
the liquid which is going to be 3 mls worth for 2 pills at once. I have
found doing 2 pills at once works best and you can use less or more,
but there is an art to this. You may end up wasting a shot before
getting it right, but if you follow my directions exactly, you should
have no problem.
Mobi's Crisping Method:
1) Take 2 MSC 100 mgs (or MSIRs or OCs of any strength) and wipe the
coating off with a damp paper towel.
2) Dry the pills with a dry paper towel making sure there is no paper
left on the pills.
3) Place the pills in a 50 ml Pyrex or Kimax beaker.
4) I prefer using a hot plate, but if you are using a gas or an
electric stove, take a frying pan and place it on the burner. Turn the
burner on medium high/high and allow the pan to get hot.
5) Place the beaker on the pan or the hot plate and shake the beaker
around for about 3 -5 minutes or until the pills take on a caramel
color with a black burn mark on the contact point of the pill with the
glass. It does not have to be completely black or molten. You just want
some caramelization to take place before crushing the pill.
6) Dump the pills into a mortar and pestle that you get at any cooking
store and crush the pills into a fine powder.
7) Take the beaker off the heat and dump all of the powder into the
beaker, shaking it a little to evenly distribute it. You can use you
hands to remove any powder clinging to the mortar, but squirt alcohol
on your hand first and dry it so as not to cause too much
contamination.
Put the beaker onto the heated pan again shake it around until the
powder starts to blacken some. You do not want it to smoke a great
deal, but it is going to turn the powder black. As soon as the last
speck of powder appears black and will not move around the beaker with
shaking, you are ready to add water.
You know the rest........now enjoy shooting drugs!!!!!!!!!!!!!
And, again, to all you assholes who in any way participated in creating a pill that is intentionally manufactured to be a pain in the ass to inject, FUCK YOU. We have broken your matrix and are currently very high. You stupid shitheads can't stop us from shooting dope whenever we feel like it, your efforts have amounted to nil. Hahahahahahahahahaha!!!!!
:skull: :smokin: ::alieneyesa:: ::armed:: ::rocker::
